Hello Bob... did you have any luck understanding what I was looking for?
"Bob Phillips" wrote in message
...
Hi Antonov,

Yes, I got it. I have emailed you a further question.

Regards

Bob


"antonov" wrote in message
...
Bob, I sent it to you.... did you get it?
"Bob Phillips" wrote in message
...
Can you send me a spreadsheet? Give it a Subject of Excel - Antonov -
VLOOKUP - Programming

--

HTH

RP
(remove nothere from the email address if mailing direct)


"antonov" wrote in message
...
Hello Bob.... I really thank you for helping out.. but... I still get
the
same error... All I've done is to change the sheets names and copy and
paste
the formula in cell J7, and commit it as you told.... I really cannot
understand what I am doing wrong...
"Bob Phillips" wrote in message
...
Antonov,

I think this is what you want



=INDEX(Sheet2!$G$1:$G$20,MATCH(Sheet1!$A$1&Sheet1! $I$1,Sheet2!$A$1:$A$4&Shee


t2!$B$1:$B$4,0))*INDEX(Sheet2!$C$1:$C$4,MATCH(Shee t1!$A$1&Sheet1!$I$1,Sheet2
!$A$1:$A$4&Sheet2!$B$1:$B$4,0))

don't forget it is anj array, so commit it with Ctrl-Shift-Enter

--

HTH

RP
(remove nothere from the email address if mailing direct)


"antonov" wrote in message
...
Bob.... ehmmm... I think I am doing something wrong....as all I get
if
I
apply the formula is "#N/A"... The formula has to go in cell J7.
The
match
has to be between A1&I1 and sheet2!A1:A4&B1:B4. Now: the table in
Sheet2
is
as follows:
(A1) CI (B1) VE (C1) 0.004
(A2) CI (B2) MI (C2) 0.003
so... say the result of the match is CI VE then I need the data in
cell
Sheet1!G1 to be multiplied by Sheet2!C1.... do you think it is
possible?
thanks again for your patience


"antonov" wrote in message
...
Thanks Bob... I will try it tomorrow at the office... will let
you
know....

"Bob Phillips" wrote in
message
...
Antonov,

That gets the value so just add *other_cell_ref on the end.

--

HTH

RP
(remove nothere from the email address if mailing direct)


"antonov" wrote in message
...
Hello Bob, thanks for the prompt reply... and what about the
calculation?
is
it possible?
"Bob Phillips" wrote in
message
...
You can use MATCH and INDEX in that way





=INDEX(Sheet2!$D$1:$D$20,MATCH(Sheet1!$A$1&Sheet1! $C$1,Sheet2!$A$1:$A$20&She
et2!$C$1:$C$20,0))

which is an array formula so commit with Ctrl-Shift-Enter.

The MATCH uses the concatenated values to lookup into tow
concatentaed
ranges, which returns ajn index in the range(s). This is
passed
to
INDEX
to
get the actual corresponding value in Column D.

--

HTH

RP
(remove nothere from the email address if mailing direct)


"antonov" wrote in message
...
hello everybody. I have a question: is it possible to have
excel
to
look
up
more cells (i.e.
=vlookup(sheet1!$A$1and$C$1,sheet2!$A$1:$C$3)
and
if
both
values are equal then multiply what's in cell sheet2! by
another
cell
in
sheet1!?