I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

a sort of sneaky way to do it is to set all of the data up with a blank cell
between the machine data indicators.
make a stacked chart of all of the data including the good parts.
select the good part section and change the axis to secodary axis.
then goto <chart<source data<series and change the range for the good
parts up or down one cell to move it on the chart.
This will allow you to have different scales for the good and bad parts.
If you want then to have the same scales another way to do it would be, if
your data is in columns to alternate the good data in one column and all of
the other data in the next column. Then just mnaking a stacked column chart
would do what you want.

"Tim Donnelly" wrote:

I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

Tim -

Try any of the links on this page:

http://peltiertech.com/Excel/ChartsH...sterStack.html

- Jon
-------
Jon Peltier, Microsoft Excel MVP
Peltier Technical Services
Tutorials and Custom Solutions
http://PeltierTech.com/
_______

Tim Donnelly wrote:
I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

I've got a similar problem. I'm graphing renewable water production versus
consumption in a building. We have 4 different sources of production and 1
source of consumption. I'd like to have a chart comparing production and
consumption each month with the production column broken down by each source.
I've tried the trick you mentioned, but the column for the water consumption
always apears overlapping the production column.

I tried setting my production range to numerals for each month (1=jan,
etc...) and setting the consumption to half numerals (1.5=jan, etc...) but
the consumption column still overlaps the production column.

Also, I'm using Office 2007, so try to respond using 2007 steps.

"bj" wrote:

a sort of sneaky way to do it is to set all of the data up with a blank cell
between the machine data indicators.
make a stacked chart of all of the data including the good parts.
select the good part section and change the axis to secodary axis.
then goto <chart<source data<series and change the range for the good
parts up or down one cell to move it on the chart.
This will allow you to have different scales for the good and bad parts.
If you want then to have the same scales another way to do it would be, if
your data is in columns to alternate the good data in one column and all of
the other data in the next column. Then just mnaking a stacked column chart
would do what you want.

"Tim Donnelly" wrote:

I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

I've written a tutorial on this type of chart:

Clustered-Stacked Column Charts -
http://peltiertech.com/WordPress/clu...column-charts/

The tutorial was based on Excel 2003, but the steps in 2007 are not
different, just the places you have to hunt to find the commands are. In
the comments I spelled out the protocol for 2007.

- Jon
-------
Jon Peltier
Peltier Technical Services, Inc.
http://peltiertech.com/



adamtaylor356 wrote:
I've got a similar problem. I'm graphing renewable water production versus
consumption in a building. We have 4 different sources of production and 1
source of consumption. I'd like to have a chart comparing production and
consumption each month with the production column broken down by each source.
I've tried the trick you mentioned, but the column for the water consumption
always apears overlapping the production column.

I tried setting my production range to numerals for each month (1=jan,
etc...) and setting the consumption to half numerals (1.5=jan, etc...) but
the consumption column still overlaps the production column.

Also, I'm using Office 2007, so try to respond using 2007 steps.

"bj" wrote:

a sort of sneaky way to do it is to set all of the data up with a blank cell
between the machine data indicators.
make a stacked chart of all of the data including the good parts.
select the good part section and change the axis to secodary axis.
then goto <chart<source data<series and change the range for the good
parts up or down one cell to move it on the chart.
This will allow you to have different scales for the good and bad parts.
If you want then to have the same scales another way to do it would be, if
your data is in columns to alternate the good data in one column and all of
the other data in the next column. Then just mnaking a stacked column chart
would do what you want.

"Tim Donnelly" wrote:

I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

Excel 2007 Chart
Stacked and clustered columns.
Using superimposed charts.
http://www.mediafire.com/file/lnzwmz...10_06_09a.xlsx

That tutorial was exactly what I needed. I've seen other replies directing
people to your cluster-stacked utility, but (no offense) I'm not going to
spend money on a utility I'm only going to use this one time on this one
report. Thanks for the tutorial though. It helped a lot.

"Jon Peltier" wrote:

I've written a tutorial on this type of chart:

Clustered-Stacked Column Charts -
http://peltiertech.com/WordPress/clu...column-charts/

The tutorial was based on Excel 2003, but the steps in 2007 are not
different, just the places you have to hunt to find the commands are. In
the comments I spelled out the protocol for 2007.

- Jon
-------
Jon Peltier
Peltier Technical Services, Inc.
http://peltiertech.com/



adamtaylor356 wrote:
I've got a similar problem. I'm graphing renewable water production versus
consumption in a building. We have 4 different sources of production and 1
source of consumption. I'd like to have a chart comparing production and
consumption each month with the production column broken down by each source.
I've tried the trick you mentioned, but the column for the water consumption
always apears overlapping the production column.

I tried setting my production range to numerals for each month (1=jan,
etc...) and setting the consumption to half numerals (1.5=jan, etc...) but
the consumption column still overlaps the production column.

Also, I'm using Office 2007, so try to respond using 2007 steps.

"bj" wrote:

a sort of sneaky way to do it is to set all of the data up with a blank cell
between the machine data indicators.
make a stacked chart of all of the data including the good parts.
select the good part section and change the axis to secodary axis.
then goto <chart<source data<series and change the range for the good
parts up or down one cell to move it on the chart.
This will allow you to have different scales for the good and bad parts.
If you want then to have the same scales another way to do it would be, if
your data is in columns to alternate the good data in one column and all of
the other data in the next column. Then just mnaking a stacked column chart
would do what you want.

"Tim Donnelly" wrote:

I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.

Adam -

The utility is for people who can't be bothered to follow a tutorial, or
who have many charts to do. The tutorial is for industrious folks who
don't mind a challenge.

- Jon
-------
Jon Peltier
Peltier Technical Services, Inc.
http://peltiertech.com/



adamtaylor356 wrote:
That tutorial was exactly what I needed. I've seen other replies directing
people to your cluster-stacked utility, but (no offense) I'm not going to
spend money on a utility I'm only going to use this one time on this one
report. Thanks for the tutorial though. It helped a lot.

"Jon Peltier" wrote:

I've written a tutorial on this type of chart:

Clustered-Stacked Column Charts -
http://peltiertech.com/WordPress/clu...column-charts/

The tutorial was based on Excel 2003, but the steps in 2007 are not
different, just the places you have to hunt to find the commands are. In
the comments I spelled out the protocol for 2007.

- Jon
-------
Jon Peltier
Peltier Technical Services, Inc.
http://peltiertech.com/



adamtaylor356 wrote:
I've got a similar problem. I'm graphing renewable water production versus
consumption in a building. We have 4 different sources of production and 1
source of consumption. I'd like to have a chart comparing production and
consumption each month with the production column broken down by each source.
I've tried the trick you mentioned, but the column for the water consumption
always apears overlapping the production column.

I tried setting my production range to numerals for each month (1=jan,
etc...) and setting the consumption to half numerals (1.5=jan, etc...) but
the consumption column still overlaps the production column.

Also, I'm using Office 2007, so try to respond using 2007 steps.

"bj" wrote:

a sort of sneaky way to do it is to set all of the data up with a blank cell
between the machine data indicators.
make a stacked chart of all of the data including the good parts.
select the good part section and change the axis to secodary axis.
then goto <chart<source data<series and change the range for the good
parts up or down one cell to move it on the chart.
This will allow you to have different scales for the good and bad parts.
If you want then to have the same scales another way to do it would be, if
your data is in columns to alternate the good data in one column and all of
the other data in the next column. Then just mnaking a stacked column chart
would do what you want.

"Tim Donnelly" wrote:

I would like to have two columns on the same chart. One will be the amount
of good parts produced by a machine. The other would be a stacked column of
scrap parts produced by the machine. The scrap parts are seperated by
certain defects, but I'd like to see their total compared to the total of
good parts.