Detecting an endless loop in the VB Editor
 

Hi,

In events programming, not using Application.enableevents = True and
False code comibination may result in an endless loop.

Is there any way to detect whether an endless loop has been
trigerred? Is there any indication in the VB editor to indicate that
there is currently no endless loop running?

I am asking this as it may take quite some time before the system runs
out of resources because of the endless loop.

Thanks in advance for the help.

Regards,
Raj

Detecting an endless loop in the VB Editor
 

On Jun 7, 3:01 am, Raj wrote:
Hi,

In events programming, not using Application.enableevents = True and
False code comibination may result in an endless loop.

Is there any way to detect whether an endless loop has been
trigerred? Is there any indication in the VB editor to indicate that
there is currently no endless loop running?

I am asking this as it may take quite some time before the system runs
out of resources because of the endless loop.

Thanks in advance for the help.

Regards,
Raj
Hi,
Click Ctrl-Break to stop the loop,
lets see the code....

Detecting an endless loop in the VB Editor
 

I don't know of a practical way to make a program smart enough to know when
it shouldn't be doing what you told it to. You can, I think, have it check
the time at the beginning of a loop and then if it spends more than <n
seconds inside the loop it can stop and display an abend message. But would
you want to do that with every loop you create in an event routine?

There is another way around it: A human can at some point get suspicious
and hit <Ctrl-Break (or is it <Ctrl-SysRq? I always get them confused),
which will cause the routine to stop and allow you to look at the debugger to
figure out what's going on; at that point you can decide whether to stop the
run, allow it to continue or fix the logic and let it go on from there.
That's helpful only when the user is also the author, of course, or at least
a VBA writer himself; if you're handing this routine to be used by others it
doesn't solve your problem.

--- "Raj" wrote:
In events programming, not using Application.enableevents = True and
False code comibination may result in an endless loop.

Is there any way to detect whether an endless loop has been
trigerred? Is there any indication in the VB editor to indicate that
there is currently no endless loop running?

I am asking this as it may take quite some time before the system runs
out of resources because of the endless loop.

Detecting an endless loop in the VB Editor
 

On Jun 7, 6:25*pm, Bob Bridges
wrote:
I don't know of a practical way to make a program smart enough to know when
it shouldn't be doing what you told it to. *You can, I think, have it check
the time at the beginning of a loop and then if it spends more than <n
seconds inside the loop it can stop and display an abend message. *But would
you want to do that with every loop you create in an event routine?

There is another way around it: *A human can at some point get suspicious
and hit <Ctrl-Break (or is it <Ctrl-SysRq? *I always get them confused),
which will cause the routine to stop and allow you to look at the debugger to
figure out what's going on; at that point you can decide whether to stop the
run, allow it to continue or fix the logic and let it go on from there. *
That's helpful only when the user is also the author, of course, or at least
a VBA writer himself; if you're handing this routine to be used by others it
doesn't solve your problem.



--- "Raj" wrote:
Ineventsprogramming, not using Application.enableevents = True and
False code comibination *may result in an endless loop.

Is there any way to detect whether an endless loop has been
trigerred? *Is there any indication in the VB editor to indicate that
there is currently no endless loop running?

I am asking this as it may take quite some time before thesystemruns
out of resources because of the endless loop.- Hide quoted text -

- Show quoted text -

Before I knew about Application.EnableEvents=TRUE, I stored a value in
a sheet if the code should not be run, and then checked this value in
the Event - if the value is true (ie "do not run event") I fired an
Exit Sub. I tried this with a Public variable - but it was a bit more
flaky...

Detecting an endless loop in the VB Editor
 

I tried this with a Public variable - but it was a bit more flaky...

Public variables can appear to behave oddly if you are editing code after
the value of a public variable has been set. This is because VBA will
determine that it needs to recompile a module or an entire project after
editing, and compilation dumps public variables out of memory, which means
they get reset to default values (0, False, vbNullString, or Nothing
depending on the data type).


--
Cordially,
Chip Pearson
Microsoft Most Valuable Professional
Excel Product Group
Pearson Software Consulting, LLC
www.cpearson.com
(email on web site)







wrote in message
...
On Jun 7, 6:25 pm, Bob Bridges
wrote:
I don't know of a practical way to make a program smart enough to know
when
it shouldn't be doing what you told it to. You can, I think, have it check
the time at the beginning of a loop and then if it spends more than <n
seconds inside the loop it can stop and display an abend message. But
would
you want to do that with every loop you create in an event routine?

There is another way around it: A human can at some point get suspicious
and hit <Ctrl-Break (or is it <Ctrl-SysRq? I always get them confused),
which will cause the routine to stop and allow you to look at the debugger
to
figure out what's going on; at that point you can decide whether to stop
the
run, allow it to continue or fix the logic and let it go on from there.
That's helpful only when the user is also the author, of course, or at
least
a VBA writer himself; if you're handing this routine to be used by others
it
doesn't solve your problem.



--- "Raj" wrote:
Ineventsprogramming, not using Application.enableevents = True and
False code comibination may result in an endless loop.

Is there any way to detect whether an endless loop has been
trigerred? Is there any indication in the VB editor to indicate that
there is currently no endless loop running?

I am asking this as it may take quite some time before thesystemruns
out of resources because of the endless loop.- Hide quoted text -

- Show quoted text -

Before I knew about Application.EnableEvents=TRUE, I stored a value in
a sheet if the code should not be run, and then checked this value in
the Event - if the value is true (ie "do not run event") I fired an
Exit Sub. I tried this with a Public variable - but it was a bit more
flaky...